# Software

> The main computational codes used by NVMERIA, grouped by field: fluid dynamics, fire, explosions, risk, wildland fire, structures, egress, piping networks, reliability.

Every code has a field of applicability, validation documentation and limits, which are stated in the report for each assignment. The list shows the codes used most often, not every tool available.

[General-purpose CFD](#g-cfd)[Fire and smoke](#g-fire)[Explosions](#g-explo)[Consequences and risk](#g-risk)[Wildland fire](#g-wild)[Structures](#g-struct)[Egress and pedestrian flows](#g-crowd)[Piping networks](#g-flow)[Reliability and human factors](#g-rel)[Decision support](#g-dec)

## General-purpose CFD

CFD codes for flow, dispersion, ventilation and heat transfer in real geometry.

Ansys

### Ansys Fluent

CFD

General-purpose CFD code using finite volumes on an unstructured mesh: it solves the Navier-Stokes equations, including in compressible flow, with modelled (RANS) or resolved (LES) turbulence, species transport, chemical reactions and heat transfer via convection, conduction and radiation. It is the tool of choice for cases where the geometry determines the outcome: buildings housing electrolysers, congested plant areas, forced ventilation, and the dispersion and accumulation of flammable gases in confined spaces.

OpenFOAM Foundation · OpenCFD

### OpenFOAM

CFDCALC

Open-source library for computational fluid dynamics, written in C++ and released under the GPL by the OpenFOAM Foundation and OpenCFD. It is used when the phenomenon requires customised solvers or the client asks for full transparency of the models: access to the source code makes it possible to check and document how the equations and physical models are implemented.

## Fire and smoke

Field, zone and one-dimensional models for fires in buildings, plants and tunnels.

Case studies [Integrated safety analysis of BESS installations](https://www.nvmeria.it/en/case-studies/#c-bess) · [Fire safety engineering for a distillation unit](https://www.nvmeria.it/en/case-studies/#c-dist) · [Fire resistance with coupled CFD and thermo-structural analyses](https://www.nvmeria.it/en/case-studies/#c-strutt) · [Emergency ventilation of an underground station](https://www.nvmeria.it/en/case-studies/#c-metro) · [Emergency ventilation of an interchange station with a network model](https://www.nvmeria.it/en/case-studies/#c-ida) · [New protected escape routes in a food production plant](https://www.nvmeria.it/en/case-studies/#c-pf) · [Fully developed fire in industrial warehouses](https://www.nvmeria.it/en/case-studies/#c-mag) · [Fire in pallets of finished product stored under tensile structures](https://www.nvmeria.it/en/case-studies/#c-oi)

NIST · Thunderhead Engineering

### FDS and PyroSim

CFDCAD

Fire Dynamics Simulator is the field model developed by NIST with Finland’s VTT: it solves a large eddy simulation form of the Navier-Stokes equations for the low-speed, thermally driven flows of a fire, that is smoke and heat transport. PyroSim is its geometric pre-processor. It is the most widely used code in performance-based fire engineering, with public verification and validation guides that support its use in technical and judicial settings.

NIST

### CFAST

CALC

NIST zone model for fire development in compartmented spaces. It suits screening and comparisons across many configurations, where a field model would require disproportionate computing time.

EQUA Simulation

### IDA Tunnel

1D

EQUA Simulation software for one-dimensional simulation of ventilation in tunnels and underground networks, including stations, shafts and connecting tunnels. It combines aeraulics, the piston effect of vehicles, the operation of fans and dampers and their control logic, and simulates fire development and smoke propagation throughout the entire structure. It enables the verification of ventilation strategies during normal operation and in emergencies, and the assessment of changing conditions along escape routes, with calculation times that allow for the analysis of numerous scenarios.

Fluidyn

### Fluidyn-PANFIRE

CALC

Three-dimensional thermal radiation model for pool, storage, warehouse and car park fires. It computes flame geometry and heat release taking account of firewalls, water curtains and topography, and maps the exposed areas around the fire.

University of Liège · ArcelorMittal

### OZONE

CALC

Zone model for natural fires in a compartment. It provides the gas temperature history used in the fire resistance assessment of structural members.

## Explosions

Deflagrations in congested geometries, detonations and blast wave propagation.

Case studies [Integrated risk analysis of an explosives storage facility](https://www.nvmeria.it/en/case-studies/#c-esp) · [Human reliability with the SHERPA method for new explosives operations](https://www.nvmeria.it/en/case-studies/#c-hra) · [Integrated safety analysis of BESS installations](https://www.nvmeria.it/en/case-studies/#c-bess) · [Rupture of a gas pipeline inside a landfall microtunnel](https://www.nvmeria.it/en/case-studies/#c-gas) · [Flammable vapour or dust: which explosion fits the damage](https://www.nvmeria.it/en/case-studies/#c-vap) · [Risk of a plant section in three configurations](https://www.nvmeria.it/en/case-studies/#c-p3d)

Viper Applied Science

### Viper::Blast

EXPLOSTRUCT

CFD code for simulating the propagation of shock waves generated by the detonation of explosives, including in complex geometries such as urban areas, industrial plants and building interiors. It takes into account reflections, channelling and shielding, and provides time histories of pressure and impulse on structures and surfaces: the explosion loads upon which the verification of structural elements and the assessment of effects on people are based.

Advanced Analysis Australia

### exploCFD

EXPLOCFDATEX

Computational fluid dynamics code by Advanced Analysis Australia for gas cloud deflagration in congested geometries and the calculation of the overpressure field. It is used instead of integral models when event severity depends mainly on plant congestion.

NUMERICS

### SPEED

EXPLOSTRUCT

Multi-material Eulerian and Lagrangian hydrocode by NUMERICS for fast transient phenomena in 2D and 3D: detonation and blast propagation, internal explosions, underwater detonations, impact and penetration, structural integrity. It comes with a library of validated material models. It is used when the explosion interacts with water, soil or structures and a gas-phase model alone is not enough.

## Consequences and risk

Consequence models, quantitative risk, atmospheric dispersion and detection.

Case studies [Integrated risk analysis of an explosives storage facility](https://www.nvmeria.it/en/case-studies/#c-esp) · [Integrated safety analysis of BESS installations](https://www.nvmeria.it/en/case-studies/#c-bess) · [Quantitative risk analysis of a hydrogen facility](https://www.nvmeria.it/en/case-studies/#c-h2) · [Risk of a plant section in three configurations](https://www.nvmeria.it/en/case-studies/#c-p3d) · [Risk from dangerous goods transport on a motorway section](https://www.nvmeria.it/en/case-studies/#c-tra) · [Fire & Gas mapping of a process area](https://www.nvmeria.it/en/case-studies/#c-fgm)

DNV

### DNV Phast and Safeti

RISKCALCEXPLO

Phast (DNV) is one of the most widely used codes for modelling the consequences of hazardous releases: dispersion, fires and explosions. It is used with the advanced 3D Explosions module, for overpressure calculated on the actual plant geometry, and the CFD Pool Fires and CFD Jet Fires modules, for radiation from pool and jet fires. Safeti, on the same calculation basis, extends the analysis to quantitative risk: individual risk on a geographical basis and societal risk expressed as F-N curves.

Gexcon

### EFFECTS

RISKCALC

Gexcon software based on the integral models of the Yellow Book (release, evaporation, dispersion, fire and explosion) and the vulnerability functions of the Green Book for effects on people and structures. Because it uses public, documented methods recognised across Europe, results can be verified by third parties: it is the right choice when a calculation has to be compared with that of regulators or party experts.

Gexcon

### RISKCURVES

RISK

Environment for territorial quantitative risk analysis, with iso-risk contours, societal risk and the contribution of individual scenarios. It shows which sources drive the result, and therefore where mitigation is most effective.

Sandia National Laboratories

### HyRAM+

RISKCALC

An open-source platform developed by Sandia National Laboratories for analysing the consequences and risks associated with hydrogen systems – both gaseous and liquid – and other alternative fuels. It integrates experimentally validated models for release, jet flow, dispersion, fire radiation and deflagration overpressure, alongside a quantitative risk analysis module based on component failure rates and damage models. These same models form the basis for the separation distances specified in NFPA 2: it is the benchmark for a sector in which the risk-based approach complements the prescriptive one.

Lakes Environmental

### AERMOD View and AERSCREEN View

DISPCALC

Lakes Environmental’s AERMOD View is the interface to the US EPA’s regulatory reference model for the atmospheric dispersion of operational emissions. Using AERSCREEN, it provides conservative screening estimates; using AERMOD, it performs detailed calculations, incorporating hourly meteorological data, topography and the wind-shadow effect of buildings, and returns concentrations and ground-level deposition at sensitive receptors. Internationally recognised and widely accepted by environmental authorities, it is the tool of choice for air quality and public exposure studies.

Micropack

### HazMap3D

RISKCADATEX

Environment for three-dimensional mapping of gas and flame detector coverage. It quantifies which fraction of credible releases is actually detected, and how quickly.

## Wildland fire

Flame front spread over real terrain and the local wind field.

Case studies [Vegetation fire and electrical equipment: reconstructing the origin](https://www.nvmeria.it/en/case-studies/#c-wfa) · [Wildland fire and an overhead line fault: cause or consequence](https://www.nvmeria.it/en/case-studies/#c-wfa2)

USDA Forest Service

### FlamMap and FARSITE

WFIRE

FlamMap is the USDA Forest Service application for analysing wildland fire behaviour, built on the models of M. A. Finney. It computes rate of spread, flame length and fireline intensity cell by cell; its Minimum Travel Time module traces fire paths and arrival times and estimates burn probability from multiple ignitions. It integrates FARSITE, which simulates front progression over time under varying weather, including spotting, the remote ignition caused by transported firebrands.

Tecnosylva

### Wildfire Analyst

WFIRE

Tecnosylva tool for analysing wildland fire behaviour, used in preliminary assessments and in the retrospective reconstruction of spread dynamics. Its speed makes it suitable for comparing many scenarios and for decision support at short notice.

USDA Forest Service

### WindNinja

WFIREDISP

Model for simulating the near-surface wind field over complex terrain. It returns the local distribution of speed and direction feeding fire spread and dispersion models, where assuming a uniform wind would lead to significant errors.

## Structures

Structural verification, including fire exposure.

Case studies [Fire resistance with coupled CFD and thermo-structural analyses](https://www.nvmeria.it/en/case-studies/#c-strutt) · [EI fire resistance of CLT floor slabs](https://www.nvmeria.it/en/case-studies/#c-xlam)

2S.I.

### PRO_SAP

FEMSTRUCT

Finite element structural analysis environment for buildings and civil works. It covers code compliance verification, seismic vulnerability assessment of existing structures and fire resistance verification of load-bearing members, modelling masonry, reinforced concrete, steel and timber.

University of Liège

### SAFIR

FEMSTRUCT

Finite element code developed at the University of Liège for structures exposed to fire, solving the thermal field and the mechanical response in sequence. It is used for fire resistance verification with natural fire curves, derived from a fire model, instead of nominal curves.

## Egress and pedestrian flows

Simulation of emergency egress and everyday pedestrian flows.

Case studies [Emergency ventilation of an underground station](https://www.nvmeria.it/en/case-studies/#c-metro) · [New protected escape routes in a food production plant](https://www.nvmeria.it/en/case-studies/#c-pf)

Thunderhead Engineering

### Pathfinder

CROWDFLOW

Agent-based egress simulator by Thunderhead Engineering, with behavioural models for exit choice and density management. It allows egress to be verified in complex geometries and evacuation times to be estimated taking occupant behaviour into account.

InControl

### Pedestrian Dynamics

CROWDFLOW

InControl Simulation Software environment for simulating large pedestrian flows in transport infrastructure, events and public spaces. It suits problems of capacity and level of service in ordinary use, rather than emergency egress.

## Piping networks

Fire and process networks, in steady and transient conditions.

Sunrise Systems

### PIPENET

FLOWCALC

Software suite for the analysis of pipework networks under steady-state and transient conditions. The Spray/Sprinkler module is designed for fire-fighting systems (sprinkler, deluge, spray, foam and water mist) in accordance with the NFPA and EN 12845 calculation methods, and verifies that design flow rates and pressures are maintained even at the most hydraulically unfavourable point. The Transient module simulates water hammer, pump start-up and valve operations, assessing overpressures and forces on the pipework to ensure the integrity of the network.

## Reliability and human factors

System reliability, safety instrumented functions and human reliability.

Case studies [Integrated risk analysis of an explosives storage facility](https://www.nvmeria.it/en/case-studies/#c-esp) · [Human reliability with the SHERPA method for new explosives operations](https://www.nvmeria.it/en/case-studies/#c-hra) · [Integrated safety analysis of BESS installations](https://www.nvmeria.it/en/case-studies/#c-bess) · [Availability of a furnace system](https://www.nvmeria.it/en/case-studies/#c-ram) · [Fault trees for the hydrogen gasholder and header](https://www.nvmeria.it/en/case-studies/#c-fta)

Analysis methods

### SHERPA and SPAR-H

HRARISK

Structured methods for human reliability analysis: SHERPA for classifying credible errors along a task sequence, SPAR-H for quantifying error probability as a function of performance shaping factors. They allow the operator to be treated as a system component, with an error probability estimated by a recognised method.

exida

### exSILentia

SILRISK

exida environment for determining and verifying the integrity level of safety instrumented functions to IEC 61508 and IEC 61511, computing probability of failure on demand and diagnostic coverage.

Atkins

### RAMP

SILRISKCALC

Tool for modelling system reliability, availability and maintainability, with state simulation and comparison of maintenance policies. It estimates the expected availability of a protection function over its whole service life, as well as its probability of failure on demand.

Analysis methods

### FTA, ETA, RBD and RAMS analysis

RISKSILCALC

Fault trees and event trees for estimating the frequency of failure sequences and the reliability of protective barriers; reliability block diagrams for the RAMS analysis of plants and systems. This step combines the severity of consequences with their expected frequency, making the result comparable with risk acceptability criteria or availability requirements.

## Decision support

Decision trees, Bayesian networks and argument maps, to structure a decision under uncertainty and make the reasoning behind it explicit.

BayesFusion

### QGeNIe

COMPLEXRISK

BayesFusion’s environment for the rapid construction of qualitative causal models: each node is a true-or-false proposition and its colour shows its degree of truth. It captures expert judgement where a fully quantitative model is not practical, shows interactively the effect of observations and decisions, and its models can be exported to GeNIe and refined into quantitative Bayesian networks.

Syncopation Software

### DPL

DECISIONRISK

A decision analysis environment that combines influence diagrams and decision trees, linked to Excel spreadsheets. It computes risk profiles, tornado sensitivity diagrams and the value of information, that is, how much it is worth reducing an uncertainty before deciding.

ReasoningLab

### Rationale

DECISIONARG

An online tool for building argument maps: claim, supporting reasons, objections and evidence laid out in a visual diagram. It makes the steps of the reasoning and the hidden assumptions explicit, and helps check how well a study’s conclusions hold up and discuss them with the client.

---
Original page: https://www.nvmeria.it/en/software/
